Other tries for the "look" are D76, D76(1:1), and/or Acufine.
-Lew

Tri-X and Xtol in 35mm is a really nice combo but to good if you're
looking for grain ...
Tri-X changed a few years ago and is less grainy now, you may look at
films like HP-5 that is a bit grainier or films from Eastern Europe or
China (all these are easily available from webshops in Germany) that
are much grainier.
Another option is to use developers like Rodinal which gives really
large grain and lots of acutance (edge sharpness).
You may also push the film but keep in mind that doing so will
increase contrast and may not suit your subject.

Claudio Bonavolta
http://www.bonavolta.ch

Often ignored in the clamour of 'my favorite developer' is
the obvious - for sharp grain you need to make _sharp_ prints:

   o A very sharp lens;
   o Used at optimum aperture (usually 5.6);
   o Glass negative carrier;
   o No vibration;
   o Precise enlarger alignment.

To find a very sharp lens you may need to try several
samples as lens-to-lens variation is often greater than
the difference between 'low-end' and 'high-end' lenses.

   A sharp grain image give the illusion that the entire
image is sharp.
   Some developers do better at producing sharp grain
patterns than others and some produce more of the effect
called "acutance" (Kodak term), which is an exageration at
the edges of transitions from high to low density in the
image.
   A traditional developer for producing both sharp grain
and acutance effects is Rodinal. Grain is greatest when used
at fairly low dilutions (say 1:25), acutance becomes greater
as the developer is diluted (say 1:50 or more) but, unlike
some other developers, the grain gets finer with dilution.
Rodinal was discontinued when Agfa went out of the
photographic materials business but is evidently still being
made by others.
   A number of other developers will produce the acutance
effect when diluted. Even D-76 or Ilford ID-11 will produce
it at 1:3 dilutions. HC-110 is another possibility.
   There are no really coarse grain films on the market now
but the old rule that fast films are grainier than slow ones
still holds so choose a fast, conventional grain film. The
last means that tabluar grain films, like the T-Max series,
or Ilford Delta series, have inherently finer grain than
conventional cubic grain films of similar speed like Tri-X
(although Tri-X is really a pretty fine grain film).
   Also, keep in mind that published pictures may have been
subjected to manipulation. One can add grain patterns in
printing or electronically and all digital image editors
have some sort of sharpening function.
   Real sharpness in photographic prints depends on having
sharp negatives and very good enlarging equipment. The
enlarging lens should be of good quality (although it does
not have to be the latest and most expensive) and the
enlarger should be well aligned and vibration-free.
   Grain can sometimes add something to an image but I
started in photography when grain was hard to avoid and have
never been a fan of grainy images.

On Aug 22, 9:22 am, Christian Sulzer <christian.sul...@inode.at>
wrote:

Try this:

Expose your film at half the ISO speed and develop for about 2/3 the
recommended time. Print on grade 3 filtration (adjust the developing
time until all your negatives print well on grade 3). You prints will
look VERY sharp and the grain will be well-defined but 'fine'.

Grain is your friend. Believe it.

First make the image sharp using good technique, then try D-76, ID-11
(about the same) and Rodinal 1:100. The later will give more latitude,
or 1:25 for super-snap.

Repeat: GRAIN IS YOUR FRIEND! The digital mavens can't so the same
thing. They get noise in the black space and think it's grain. Pity.

A sturdy tripod is the first step toward maximum sharpness regardless
of shutter speed, format or camera type. Second step: cable release.
Third step: mirror lock (if you have one). There are many valid
excuses for not using a tripod but nothing will contribute more to a
sharp detailed negative than a well made tripod. If you want to pursue
this subject further consider reading Barry Thornton's Edge of
Darkness. As to grain I have always looked to minimize it so can't
help there but cropping at the enlargement stage is a sure way to
increase grain size.

http://www.digoliardi.net/images/dawn.jpg

Is that the kind of grain you want?
That's a scan from a print and the grain is not as sharp in the JPG as the
print which was on 14" paper.

Tri-X in Rodinal 1+50 was *quite* grainy in my experience,
to the point of being a special effect for me.  The Massive
Dev Chart suggests times for Tri-X at various EIs; I recall using
Tri-X at EI 200, Rodinal 1+50, 9 minutes @ 20C, but you'll need to
run some tests of your own.

Dana

Dana